Accessories

One of the things some gun owners—engineers or fairly well-educated hobbyists who have a good grasp of mechanical things—ask about is how to handle the different kinds of pins in their guns. Particularly, they often want to know if their punches are the right ones, or if they can use a slightly different one without damaging their pins.

We recently reviewed three 38 Special revolvers that cost about $400 and thought we would increase our budget and caliber size, and then sourced three revolvers each costing about $500 in three different big-bore calibers: 44 Special, 45 ACP, and 45 Colt, often called 45 Long Colt (LC) to ensure it's not mixed up with the Auto Colt cartridge. The three revolvers included two Charter Arms products, the Classic Bulldog in 44 Special and the newer Pitbull in 45 ACP, plus the Taurus Public Defender Polymer chambered in .410 shotshell and 45 LC.

Even though these were new revolvers, we still performed a range-rod test since there was a bit of side-to-side wiggle in the cylinders of all the revolvers. Range rods check the alignment of the chambers to the barrel bore. We also noted that the action of the Taurus seemed a bit stiff; our initial dry firing in double action found the cylinder would not fully index to the next chamber at times. Dry firing took care of the indexing issue, and all passed the range rod test. We also noted during the range-rod test the barrel of the Pitbull was not fully screwed into the frame. It was off by a fraction of a turn, enough to cock the front sight to the left when aiming the revolver. It is unacceptable that a gun leaves the factory in this condition. We anticipated and needed to use Kentucky windage with the Pitbull at the range.

In the past Charter Arms revolvers have been favorably rated, but in these two examples we found exception. The not-fully-screwed-down barrel was also the reason the cylinder-to-barrel gap was so large. We measured the gap between the front of the cylinder and the forcing cone at the rear of the barrel using feeler gauges from Brownells (606-950-252WB) and found a gap of 0.010 inches for the Pitbull and the Bulldog Classic and the Taurus at 0.005 inch. A gap of 0.003 inches is desirable for a competition revolver, but up to 0.006 inches is often found. A large gap allows more gas to escape, reducing the bullet's velocity. It also means there is more flash, and if the chamber and cylinder are not perfectly aligned, a user might experience splash from burning powders and bits of shaved bullet metal. We did not experience any splash with the Charter Arms revolvers. We did note that the Classic Bulldog had about 30 fps more than the published data for Hornady Critical Defense165-grain FTX bullet, which is 900 fps out of 2.5-inch barrel. The 3-inch barrel of Bulldog must have helped increase velocity. The Pitbull had noticeably less muzzle velocity compared to factory data. We assumed the reduction came because the Pitbull has a 2.5-inch barrel and the factory data for the cartridges use either a 4- or 5-inch barrel. Reduced muzzle velocity also occurred in the Taurus.

A common feature of all three revolvers was a safety transfer bar. This system prevents the hammer from striking the firing pin unless the trigger is pulled fully to the rear.

These revolvers are made for close-in work, but we still tested accuracy out to 25 yards. Since the Taurus offers the ability to fire .410 shotshells as well as cartridges, we sourced some CCI shot cartridges in 44 Special. CCI manufactures shotshells in 45 ACP, but warns against using the the cartridges in revolvers since the crimp that holds the shot in the cartridge case may interfere with the rotation of cylinder after being fired. One of our team members regularly carries a revolver loaded with bird shot cartridges and bullet cartridges when we walks his dog in the woods. He's equipped to deal with snakes as well as bears, depending on what chamber he lets fly.

Magazines for the 1911 pistol have evolved more during the past two decades than during any other time since the pistol's introduction. The bane of the 1911 is cheaply made magazines, with poor ammunition close behind. For many years, the only choices were Colt factory magazines, which were usually high quality, then GI magazines, and poorly made gun-show magazines. Some were marked COLT 45 on the base in bold letters, and these usually meant the shooter was the real deal. At a time when new Colt magazines were around $15, aftermarket magazines sold for as little as $4, and most of them were not worth the aggravation. GI magazines were good quality, but shooters often found them bent and worn out, unless they were new in the wrapper. Quite a bit of barrel feed-ramp polish and tuning of extractors went on that probably was tied to ammunition and magazine problems. Some of the aftermarket magazines were not properly welded. In other cases, the follower was too tight in the magazine body; and in other instances, the magazine springs were weak. Others had poorly attached buttplates, that gave way when dropped on the ground during IPSC competition. Some survived, others did not.

The basic construction of the magazine itself has changed from sheet steel to aluminum and plastic followers versus metal followers. We have examined quite a few magazines that invited a situation called false slide lock. The follower appeared to catch the slide lock, but the slide lock was actually on the wrong shelf, which isn't good for any of the parts. A 1911 feeds by the loading block on the bottom of the slide stripping the cartridge forward as the slide moves forward. The cartridge case rim catches under the extractor and is pressed forward. Some feel that it is a good thing that the bullet nose snugs a little over the feed ramp and bumps the cartridge case head into the breech face as the cartridge enters the chamber. Some magazines, notably the Wilson Combat, allow the bullet nose to strike much higher on the ramp, which results in missing the feed ramp's edges more so than others.

…

The civilian-available semi-auto versions of what began as expensive SBR's (short-barrel rifles) or true submachine guns are advertised as having good accuracy and reliability while offering a more compact package than a rifle and higher round counts than most handguns. For the task of guarding the castle, we've been around the block a time or two, and have suitable choices for nearly anyone — great pistols, rifles, and shotguns. For this test, we had to suspend any preconceived notions of what we might prefer for home defense and test these firearms based on their own merits. Those merits, we found, are few. If you are shooting for fun and simply making brass, anything that goes bang is suitable. We'll get into the reasons for these judgments, but we like to be clear up front. The SIG Sauer MPX-P is one expensive means of not accomplishing much. The Uzi Pro pistol has drawbacks that made shooting downright frustrating. The MasterPiece Arms Defender proved to be the best of the three and has merit in a defensive situation, within certain narrow parameters. We arrived at this decision by using personal-defense criteria as the overriding factor in providing Buy/Don't Buy advice to our loyal readers. So, in more detail, here are our reasons for making these assessments. Our 9mm Luger ammunition for this test included a 158-grain lead round nose choice from Tomkatammo.com ($18/50 rounds). We also used Black Hills Ammunition 124-grain jacketed hollow points from VenturaMunitions.com ($14/20), a Black Hills Ammunition 115-grain EXP, an Extra Power load not quite in +P territory, also available from VenturaMunitions.com, ($17/20), and a SIG Sauer 115-grain full-metal-jacket load from Cabelas.com ($28/50). Others included the SIG Sauer 124-grain V Crown jacketed hollow point from Luckygunner.com ($16.75/20), and the Hornady American Gunner 124-grain XTP +P from MidwayUSA.com ($14.79/20). We used the Tomkat 158-grain, the Black Hills 124-grain JHP, and the SIG 115-grain FMJ load in benchrest accuracy testing.

The shotgun is seen by many as the best choice for personal defense and especially home defense. The most powerful portable shoulder-fired weapon used for self preservation, the 12-gauge shotgun offers a multiple-projectile load that has been proven effective in close-quarters defense. With slug loads, it is even suitable for defense against large, dangerous animals. In rural defense, there are plenty of deadly predators in the country, feral dogs, mountain lions, and other dangerous animals that only an aggressive counterattack will stop. But without proper firearm and load selection, as well as training, the shotgun will be underutilized. More than one citizen has defended himself with the shotgun, and common sense tells us that we should have one in the home.

In this test, the shotguns we chose are among the best in their price range. The choices range from a pedestrian bead-sighted model to a tactical model with an AR-15 type stock. While self-loaders rule the day at 3 Gun competitions and are very reliable, a dirty pump will work when a dirty automatic will not. We have seen self-loaders malfunction during our test programs, and we know the pump-action shotgun is relatively easy to master, as long as you get quality training so you're confident in your skills and sure in your manipulation.

With this in mind, we chose three likely shotguns for home defense. The top end of the budget was $450, but we would prefer to spend less to get a good pump-action gun, if we could. We fired them with practice loads, home defense loads, good loads suitable for pest and predators, and slugs suitable for defense against large animals. We used five different loads for testing these shotguns. We tried to find the most economical offerings in bulk. This included the Fiocchi 12HV75 birdshot ($97 for 250 shotshells from CheaperThanDirt.com) Fiocchi 1-ounce Aero slugs ($8.10/10 from VenturaMunitions.com), Hornady 86240 Critical Defense 00 buckshot loads ($11.08/10 from CheaperThanDirt.com), Hornady's Varmint Express, a load using 24 pellets at 1350 fps ($16/10 from Gandermountain.com), and Winchester 3-inch 12-gauge 00 buckshot loads (No. XB12300VB, $17/15 from CheaperThanDirt.com) This selection covered the likely uses for personal defense, predators, and even large animals. Each shotgun was fired with 50 birdshot shells, 10 of each of the buckshot loads, and 10 Fiocchi slugs, for a total of at least 90 shells per gun. This is punishing work and was not accomplished in a single range session. We fired mainly the light-kicking birdshot to learn how to function the guns quickly and determine their smoothness and ergonomics.

Here are the results.

In my years working on guns, I have seen a large number of totally botched bedding jobs. In fact, you would be shocked to see what people do to their guns' bedding to increase the accuracy of a rifle. But do you know how to spot the most common mistakes in bedding, thereby giving you a leg up in improving a gun's accuracy, or avoiding it altogether? Following are the most common problems shooters should watch for:

Germany has always been a leader in firearms development both for military and sporting use. The country also has a rich history of hunting. We wanted to take a look at two rifles with Teutonic hunting heritage, so we asked our dealers to wrangle up a Mauser M12 and Blaser R8. If there ever was an iconic bolt-action rifle on both sides of the Atlantic, it is the Mauser. Since 1871, Mauser has produced countless military and sporting bolt-action rifles. Mauser M98 rifles have been copied by many other rifle makers. Hallmark Mauser design features, like the action, three-position safety, and internal box magazine are built into rifles made by companies like Rigby, Winchester, CZ, Kimber, and others. The M12, however, is not a control-feed bolt action but is actually a push-feed bolt like a Remington, Sako, Weatherby, and others.

The Blaser (pronounced BLAH-zer) is a unique take on the bolt-action rifle because it uses a straight-pull bolt and offers interchange barrels in a range of calibers for gophers to elephants. Blazer had made a name for itself as an innovator of luxury hunting rifles, and though it could be debated that this German rifle is over engineered, we found some innovative features on a hunting rifle we didn't know we needed or wanted.

Either rifle would make an excellent deer rifle, we found, as well as top choices to take black bears, wild pigs, speed goats, and other hooved North American game. They both performed well in operation and in accuracy and after spending quality time with them, we can see why they command such a high price.

Both rifles were chambered in 30-06 Springfield, which is the benchmark caliber for American hunting cartridges. Our testers have a lot of experience with the cartridge, and we suspect that every bolt-action hunting rifle currently sold in the U.S. is available in 30-06. The round is versatile, easily found in stores, offers a range of bullet types and weights, and is at the upper level of tolerable recoil, especially when shooting the round out of lightweight hunting rifles. Both of these rifles hovered at seven pounds unscoped. For ammo in this test, we used Black Hills Gold loaded with a 180-grain Nosler AccuBond bullet and two hunting rounds from Hornady: Full Boar with a 165-grain GMX bullet and American Whitetail with a 150-grain InterLock bullet.

We mounted the rifles with the same optic, a SIG Tango6 2-12x40mm ($1600; CheaperThanDirt.com). This is a first focal plane-reticle scope, so the reticle increases and decreases in size as the magnification is increased or decreased. Testers liked this FFP scope because the milling reticle can be used at any magnification to estimate range. The Tango6 is equipped with an illuminated MOA Milling reticle. We could adjust reticle illumination as needed, and if we forgot to turn it off, the scope automatically turns off the illumination after six minutes of rest and powers back on as soon as it senses motion. We would have liked a parallax adjustment knob to really fine-tune the reticle, since we noticed the reticle moved ever so slightly as we moved our head and eye. Not a lot of movement, but enough to note. The scope also features Zerolock turrets, which means you can't lose zero if you rotate the turrets too much in either direction. Turret dials need to be pulled out to make adjustments then pushed back. Adjustments could be felt and seen easily, so getting our dope was simple after bore sighting. All adjustments were clearly marked, which we liked. The magnification ring used two fiber-optic dots that glowed to give the user a heads up on the magnification the scope was set at. Turrets and the magnification ring were toothy, with lots of texture, so rotating the dials was effortless. We could adjust the reticle easily while looking at it on target. For mid-range and typical hunting distances, we think the SIG scope would be a fine choice on these rifles. Where the bullet hits the paper is the real test of how well these rifles will do in the game field and deer stands. Here are the details on these luxury game getters.

It could be argued that the AR pistol evolved out of a desire and need for shooters to own a legal short-barrel rifle-caliber weapon without having to jump through BATFE hoops or pay for a tax stamp to own an SBR (short-barreled rifle). The difference between an AR rifle and pistol comes down to the pistol not being compatible nor able to attach a stock. We wanted to take a look at these AR pistols for home defense and other uses where a compact firearm makes sense, because they offer a number of benefits over a conventional AR rifle, mainly, being more maneuverable while being chambered in a rifle caliber and being compatible with common AR-15 magazines. We acquired three examples, a Spike's Tactical The Jack custom build, a CMMG Mk4 K, and a Kel-Tec PLR-16. The Spike's and CMMG are true AR-15 mechanisms reconfigured to a pistol, while the Kel-Tec uses a different operating mechanism. All three are chambered in 5.56mm NATO/223 Rem. and all are compatible with AR-15 magazines.

We tested these pistols for accuracy, performance, reliability, compatibility with a range of AR-15 magazines, maintenance, ability to be customized, and cost. We found that the Kel-Tec was inexpensive compared to the CMMG and Spike's Tactical pistols. The Kel-Tec, however, needed to be operated differently. The CMMG and Spike's were an easy transition from AR rifle to AR pistol. An AR pistol, as we found out, is nearly as effective as a full-size AR at close to mid range. With the right ammunition, they could be tuned to be a very capable home-defense choice for anyone in the family competent to operate a firearm. Namely, using frangibles to limit overpenetration through walls and doors while still supplying lots of pop.

The AR pistol's edge is its size, but it is also a disadvantage, as an AR pistol is not as easy to shoot as a rifle or a traditional handgun. They are large and require two hands to effectively deliver accurate shots. You could get off a few shots holding an AR pistol with one hand, but the weight of the pistol causes muscle fatigue. A typical full-size handgun may weigh more than 2 pounds loaded, compared to these AR pistols, which weighed from 3.2 to 6 pounds unloaded. Add a pound or more for a 30-round magazine, and you've got a sidearm that would wear out nearly anyone who didn't transport them with a sling, just as you would with a rifle. We used one of the SIG SBX Pistol Stabilizing Braces ($149; SIGSauer.com) and found we liked to use the brace differently than intended, which we will get into shortly.

We also fired the pistols using a Blackhawk Storm Sling ($33.95; Blackhawk.com), a single-point sling with a built-in bungee cord, which many team members felt was an excellent way to carry and control the pistol. We tested with three different AR-15 magazines, including a Brownells USGI CS (Brownells.com; $14) constructed of aluminum, and two polymer magazines, the Magpul PMag Gen2 (Brownells.com; $12.30), and the FAB Defense Ultimag (TheMakoGroup.com; $25). For fast reloads, we also used a Kydex AR magazine carrier from IBX Tactical (IBXTactical.com; $35).

Building an AR pistol is not just a matter of installing a short barrel in a upper receiver and swapping out the receiver extension/buffer tube. Short barrels lose velocity and provide less dwell time for the projectile, so manufacturers need to tune and time the mechanism. A short barrel also needs to work on a range of loads from low- to high-quality ammunition. Reliability can be an issue.

Hands down, the CMMG and Spike's offered more customization than the Kel-Tec because they are compatible with a range of AR-15 aftermarket products — triggers, rails, pistol grips, BUIS, and more. The Kel-Tec is not as compatible. Also, for those testers already familiar with an AR-15, the CMMG and Spike's were much easier to maintain. But there's much more to consider, which we relate below:

Patterning performance was a slight disappointment, with a 59-41 pattern using the clay target load and a 62-38 pattern with the steel shot. There was one 3-inch hole in the upper right quadrant of the lead shot pattern and eight hits outside the 20-inch center circle — mainly to the right. Not quite as tight as the Browning, but not considered a deal killer. Just like the Winchester and Browning, the Mossberg features a red fiber optic bar that is quite easy to see and allows for easy barrel alignment on targets. We noted that the checkering on the Mossberg's forearm and stock was a little less sharp than we would have liked and did not have the comfortable feel of the Dura-Touch coating on the Winchester and Browning. It was about the same as the Beretta, although we did not think it severely hindered our handling of the shotgun or our target acquisition.

Waterfowl sportsmen have greatly changed from the days of market hunters where the daily goal was simply to put huge numbers of birds on the ground in an attempt to satisfy the family dinner needs. Of course, today's waterfowl hunters are strictly limited by migratory bird regulations restricting waterfowl hunting to non-toxic shot with very reduced bag limits on both ducks and geese.

In a way, semiautomatic shotguns designed for waterfowl hunters are like little babies in a beauty pageant. While the parents may think their youngster is the cutest thing on the planet, the pageant judges always apply their own standards and personal preferences in selecting the best in show. This similarity was brought to our attention when a reader asked for a ranking of the best semiautomatic 12-gauge shotguns for bringing down ducks and geese. Without specifying some parameters — such as most used, best handling, affordability, reliability, and a variety of other factors — there can be no single best waterfowl semiautomatic. However, to provide our readers with some options in selecting their best smokepole, we were able to come up with a comparison of four popular, moderately priced semiautomatic waterfowl shotguns. The models included a Browning Maxus, listing for $1520; a Mossberg Model 930 Waterfowl, listing for $797; a Beretta Model A300 Outlander, listing for $845; and a Winchester Super X3, with a suggested retail of $1200. Each was found to feature both favorable and unfavorable elements that varied in importance with each member of our test team. In the end, the patterning-board performance and pocketbook impact proved to be the main separating factors in our ranking.

Our selection of ammunition to test the functioning ability, patterning performance and felt recoil of the semiautomatics included both clay-target loads and a typical waterfowl load. For clays, we used the recently introduced Browning BPT 2.75-inch, 3 dram equivalent loads packing 1 1/8 ounce of No. 7.5 shot with an average muzzle velocity of 1200 fps; and B&P Competition One 2.75-inch, 28-gram loads featuring 1 ounce of No. 7.5 shot with an average muzzle velocity of 1160 fps. To test the shotguns with duck loads, we selected Federal Premium Tungsten 3-inch, 3 dram equivalent No. 2 shot loads with an average muzzle velocity of 1,400 feet per second. Here are our findings:

In the October 2010 issue we published a report on 380 ACP defense loads. The work was interesting and reader feedback intensive. During the tests, the loads proved accurate and reliable. The problem was the balance of expansion and penetration. We had either adequate expansion or good penetration but not each in the same loading. Some loads penetrated as little as 9 inches, with the average load at 12-13 inches. Expansion was modest in most cases. As a result, we felt that the full-metal-jacketed non-expanding bullet was a viable choice because there was a chance it would reach vital areas and create a stoppage. Surprisingly, even FMJ loads penetrated but 14 inches in water in that test. So, the search was on for a loading that might offer superior performance to the original test choices.

This time, we tested ten different loads using the same media — water and water jugs — and came away with a couple of loads that showed good promise for personal defense.

Since our initial test, many readers have continued to ask us about the effectiveness of the 380 ACP outside the ability to make highly accurate cranial shots. If the bullet cannot be counted on to reach the vitals, then it would hardly be of much use even if it did expand. However, FMJ loads do not necessarily solve every problem. A lightweight FMJ bullet is far more likely to stop short in penetration than a heavier bullet of moderate velocity. Often, a heavier-for-the-caliber-bullet will penetrate more even at lower velocity.

In our experience, modern shooters tend to look at the 380 as a lighter alternative to the 9mm, but a better comparison is between the 38 Special snubnose and the 380. So, as a point of reference, we included a middle-of-the road 125-grain JHP 38 Special +P load fired from a 2-inch-barrel revolver to represent an average for performance with the 125-grain JHP. It makes a striking example of how the 380 ACP fares against what we believe is at least an adequate 38 Special load. Also, for your convenience, we've listed the performance of the first round of 380 ACP loads we tested six years ago. Also, the top-ranked loads from the first test were the Fiocchi FMJ 95-grain No. 380FMJB and Speer Gold Dot 90-gr. No. 23606.

Ruger is rolling out additional support for its new line of rimfire suppressors, the Silent-SR 22 line.

The Ruger Silent-SR sound suppressor was designed and built by Ruger utilizing fluid dynamic simulation and computer numeric controlled (CNC) machining equipment. Based on samples we've handled, the Ruger Silent-SR is easy to disassemble and clean. Each piece snaps together to seal the baffles and keep the byproducts of combustion away from the tube and end caps.

It is also strong and light, utilizing a titanium tube, aluminum rear cap, and stainless steel threaded mount, baffles and front cap. It measures 5.37 inches in length, 1.1-inch in diameter, and weighs 6.3 ounces.

Of course, what matters is how it reduces sound pressure levels of 22 LR, 22 WMR and 17 HMR pistols and rifles by up to 40 dB. It features a standard 1⁄2-28 thread pattern for compatibility with most threaded rimfire firearms.

The outer tube and muzzle mount are interlocked to prevent accidental disassembly when removing the suppressor from your firearm. A disassembly tool is included.

Also, Ruger is making it easier to attach the suppressor to your existing SR22 pistol.

The Ruger SR22 Threaded Barrel Kit 90520, $150, is a genuine Ruger factory accessory compatible with Ruger SR22 pistols bearing serial numbers 361-7XXXX and higher.

The threaded barrel accepts any 1⁄2-28 (Class 2A) muzzle device, including the Ruger Silent-SR. This kit contains a factory-manufactured stainless steel barrel for optimal fit and function. Barrel changing is quick and easy with no gunsmithing required, and a barrel cap, adapter, and wrench included. Note that the replacement barrel does not fit the 4.5-inch-length barrel model.

Worth noting: Ruger cannot bill to or ship to the following states and cities: California, Connecticut, Washington DC, New York, and Chicago, IL.